Spyderco Standard Wire Clip Replacement Deep Carry Titanium Clip
This clip was designed specifically for Spyderco models that use their wire clip.
Whether or not the clip will work with a specific model depends on where the clip screw is in relation to the ‘channel tines’ (where the clip is held in the scales). If the screw is high in relation to those channels, there isn’t room to get a wrench on to tighten the clip down. If the screw is in the middle or lower area, the clip will work. Please see below for a list of compatible and incompatible models.
They are made here in Washington state from domestic 6AL-4V titanium, and are hand-formed and finished.
Each clip carries a lifetime guarantee. Model Compatibility:
Spyderco:
WILL FIT
The following models that use a connected screw/barrel setup to hold the clip on the knife. On these models, if the screw and barrel both have drives, you need only to loosen the screw, then tighten it down from the opposite side once the clip is installed. If the screw has a drive, but the barrel side is plain (no drive), the screw and barrel need to be removed (before installation of the new clip), then re-installed with the screw head on the opposite side of the knife. The design of these knives puts the screw too high in relation to the ‘tine channels’ to get a driver through the access hole on the clip and onto the screw when the clip is place. But by flipping the barrel/screw around, it works well, as the clip can be tightened from the opposite side.
This clip was designed specifically for Spyderco models that use their wire clip.
Whether or not the clip will work with a specific model depends on where the clip screw is in relation to the ‘channel tines’ (where the clip is held in the scales). If the screw is high in relation to those channels, there isn’t room to get a wrench on to tighten the clip down. If the screw is in the middle or lower area, the clip will work. Please see below for a list of compatible and incompatible models.
They are made here in Washington state from domestic 6AL-4V titanium, and are hand-formed and finished.
Each clip carries a lifetime guarantee. Model Compatibility:
Spyderco:
WILL FIT
- Autonomy 1
- Caly 3
- Caly 3.5
- Chicago
- Dragonfly 2
- Lil Native Compression Lock (will not fit Lockback version)
- Manix 2 Lightweight (Pictured)
- Para 3 Lightweight
- Poliwog
- Sage 5 CF
- Sage 5 Lightweight
- Schempp Bowie (fits well with some effort)
- Siren
- Slysz Bowie (newer versions - will not fit the Gen 1 version)
- SpydieChef (newest ‘black screw’ version - will not fit older ‘silver screw’ models)
- Squeak
- Techno 1
- Techno 2 (fits older ‘high clip screw’ models with some effort'; fits newer ‘mid clip screw’ models easily)
- UKPK
- Urban
- Urban Lightweight
- Watu
The following models that use a connected screw/barrel setup to hold the clip on the knife. On these models, if the screw and barrel both have drives, you need only to loosen the screw, then tighten it down from the opposite side once the clip is installed. If the screw has a drive, but the barrel side is plain (no drive), the screw and barrel need to be removed (before installation of the new clip), then re-installed with the screw head on the opposite side of the knife. The design of these knives puts the screw too high in relation to the ‘tine channels’ to get a driver through the access hole on the clip and onto the screw when the clip is place. But by flipping the barrel/screw around, it works well, as the clip can be tightened from the opposite side.
- Chaparral CF
- Chaparral FRN
- Ikuchi
- Kapara
- UKPK FRN
- Black Bird
- Core
- Baby Core
- Italico
- MKM
- Pelican Liner Lock
- Radius (Blade HQ Jade Exclusive)
- Gungnir (Wire Clip Model)
- Avant
- X Tao CF (Carbon Fiber)
- Vox Dapper
- Drift G10 (with some clip modifications)
- Pinion
- Stout
